Program card servo - AGF RC

Servo programming card - AGF RC
This is the "Plug and Play" USB program card, easy to use and program the AGFrc servo. Please note that this USB program card can only be used for AGFrc servos with ASS branding, such as servos in the A11, A50, A62, A66 A73, A80, A81 series).

Download the software here: https://www.agfrc.com/index.php?id=download-center, you can download the ".exe" file directly or the zip file as required.

System requirement
1. Operating voltage: USB （5V / 500mA）.
2. Operating system: Windows XP / Windows Vista / Windows 7 / Windows 8 / windows10 (32 / 64bit).
3. Application: AGFrc programmable servos with ASSmarked.

Software menu instruction


Parameter function instruction
1. Servo angle: set servo rotation angle
2. Servo neutral: Set the servo neutral position
Note: While the transmitter is rotating in the neutral position, if the servo does not remain in the corresponding position, it can modify this value to adjust the servo horn. This is equivalent to adjusting the transmitter channel.
3. PWM Power: Adjust servo output power. The higher the power, the higher the servo torque and speed, and the higher the current consumption.
4. Damping factor: set servo damping.
5. Sensitivity: adjust servo deadband (sensitivity).
6. Soft start: slow restoration when the servo is switched on. Once powered up, the servo will slowly turn to the position of the current input signal.
Note: This function is designed to prevent damage due to incorrect servo mounting during power-up.
7. Reverse: set normal and reverse servo rotation.
8. Narrow band: FUTABA SR mode
9. SANWA SSR: SANWA SSR mode
Note: if you enable this function, it may support the high-speed SANWA SSR mode. The servo angle may not be precise and must be readjusted.
10. Lost PPM Protect: Protection against signal loss, there are three functions for selection,
one. Release: Non-Protection
b. Hold position: remain in position before loss of signal
c. Go to neutral position: return to neutral position (position 1500uS)
11. Over Load Protect: set servo lock protection, there are three levels, ticked to activate protection.
Level 1: set start time and power value of primary protection.
Level 2: set start time and power value of secondary protection.
Level 3: set start time and power value for tertiary protection.
Note: the left side is used to set the protection start time, the right side is used to set the output power value after
activating start protection.
12Servo information: Servo information. Including servo model, version date, firmware name.
Servo name: servo model
Manufacture: servo version date
Firmware: servo firmware name
13. Read: Read the servo parameter from the software interface.
14. Write: Write the current parameter to the servo.
15. Open: Open the servo parameter file: Open the servo parameter file that has been saved on the computer.
16. Save: Save the current servo parameter to the computer
17. UPF: servo firmware upgrade function.
18. Default: restores default settings.
19. Exit: Exit and close configuration software

1-2
Parameter function instruction



1. PWM Power: Adjust servo output power. The higher the power, the higher the torque and speed of the servo, the higher the current consumption.
2. ProPTL: 3.0s: The start time of the servo lock protection (unit: seconds), while the servo is locked and lasts until the set value, the protection will be active and the servo will stop working.
3. Reverse: Set the normal and reverse rotation of the servo
4. Servo information: Servo information. Including servo model, version date, firmware name.
Servo name: servo model
Manufacture: servo version date
Firmware: servo firmware name
5. Read: Read the servo parameter from the software interface.
6. Write: Write the current parameter to the servo.
7. Open: Open the servo parameter file: Open the servo parameter file that has been saved on the computer.
8. Save: Save the current servo parameter to the computer
9. UPF: servo firmware upgrade function.
10. Default: restore factory default settings
11. Quit: exit and close configuration software

















Problem and solution
If it cannot be programmed, how to inspect,
1) Check whether the connection is correct or not;
2) Please check whether the programming software is the latest version or not;
3) If the connection still fails, please send an e-mail to support@agfrc.com for help.